As everyone in the EPC industry knows, the drying process of the pattern after coating is an important link related to the quality and cost of the casting products. However, drying the EPC pattern requires a lot of heat and takes a long time. After each coating, the pattern usually needs to be dried for 24-72 hours. The existing method is to establish a drying room (drying room) and use drying equipment to dry! Such as fuel burning, electric heating, pipe heating, etc
The purpose is to heat the air medium around the EPC pattern, keep the temperature of the drying room (drying room) at 45~50 ℃, volatilize the moisture of the pattern, and then discharge the hot and wet air as waste gas. However, some traditional EPC drying equipment occupy a large area, and many small and medium-sized EPC drying equipment have uneven drying, long drying cycle and large energy consumption
The energy-saving structure transformation of EPC drying room can be summarized as three points: first, reduce the relative humidity; 2、 Raise the temperature appropriately; 3、 Achieve uniform air distribution. However, the appearance of PD-45G EPC coating drying room dehumidifier and PD series heating, heating, drying and dehumidifying integrated machine solved the above problems, transferring the heat in the air to the drying room, with fast heating speed, good moisture removal effect and lower energy consumption cost
While PD-45G EPC paint drying room dehumidifier and PD series heating, drying and dehumidifying integrated machine are intelligent drying and dehumidifying integrated equipment. The temperature, humidity and wind speed can be set through the intelligent control panel to meet the needs of EPC drying process, and there is no need to arrange workers to watch over and add fuel. Users who have been successfully transformed say they can finally sleep soundly, Set the parameters in advance, sleep and wake up with peace of mind. The quality of EPC products after drying is better than before, which saves worry. The whole drying process will not produce pollutants, but also save operating costs
PD-45G EPC coating drying room dehumidifier and PD series heating, heating, drying and dehumidifying integrated machine still have many advantages. For example, compared with microwave dryer, the price is much lower than that of microwave dryer; Compared with the electric heating dryer, as long as the temperature of the EPC drying room is kept at about 40~50 ℃ and the relative humidity is controlled at about 30% RH, the drying efficiency will be increased by about 40%, and about two-thirds of the electricity can be saved. Moreover, the air outlet is more uniform, the evaporated mold after drying is not easy to crack, and the strength is high. Users who have experienced it are full of praise
When drying EPC, PD-45G EPC coating drying room dehumidifier and PD series heating, drying and dehumidifying integrated machine can use electricity without burning electricity. What do you mean by that? In other words, in the process of drying the lost foam, only a small amount of electric energy is needed to drive the operation, instead of relying on electricity for heating. After a set of drying process, you will find that its power consumption is only a fraction of the traditional electric dryer
In view of the demand for energy saving dehumidification and drying in drying rooms and drying rooms, the PD-45G EPC coating drying room dehumidifier and the PD series heating, drying and dehumidifying integrated machine developed and produced by the electrical appliances can not only quickly remove the moisture in the drying room, effectively control the humidity in the drying room during the whole drying process, but also can be equipped with electric heating of corresponding power to assist heating, thus greatly accelerating the drying speed, It effectively improves the utilization rate of the drying room and the drying quality
PD-45G EPC coating drying room dehumidifier and PD series heating, heating, drying and dehumidifying integrated machine are high efficiency heating type drying and dehumidifying equipment, integrating heating, heating and air dehumidification functions (applicable to the temperature range of 5-55 ℃); It is composed of compressor, evaporator, casing condenser, centrifugal fan, electric heating system and other major components. During the dehumidification process, the electric heating system is used to assist in heating up. There is no exhaust during the dehumidification process, and the energy consumption is low
For the traditional drying method, the dehumidification speed is faster and the power is saved; And it is more environmentally friendly and energy-saving. Using a small amount of electric energy to run can achieve the effect of heating and air dehumidification. There is no waste gas pollution, no combustible emissions, no toxic gas emissions, and keep the environment clean! Welcome to inquire the details of EPC coating drying equipment and dehumidifier in EPC coating drying room
Technical parameters of PD-45G EPC coating drying room dehumidifier and PD series heating, heating, drying and dehumidifying integrated machine:
Model selection of integrated dryer and dehumidifier: select the appropriate model according to the overall humidity load of the actual drying room, specifically calculate the cooling capacity according to its area, floor height, evaporation capacity of drying water, initial humidity value, target humidity value, indoor sealing effect, moisture dissipation source, fresh air supply and other comprehensive factors, Only after other key data such as dehumidification amount per unit time can the required model be correctly selected
To sum up, it can be seen that the PD-45G EPC paint drying room dehumidifier and the PD series heating, heating, drying and dehumidifying integrated machine are mainstream EPC drying equipment at present, replacing the traditional electricity, coal boilers, natural gas boilers, firewood, fuel oil and other high energy consumption, high pollution drying equipment. It conforms to the national environmental protection standards, is a new energy, and will become a widely used drying equipment in the future
If you are not very satisfied with the EPC drying equipment currently used, you can learn about the PD-45G EPC coating drying room dehumidifier and PD series heating, heating, drying and dehumidifying integrated machine introduced above. First, according to your drying situation, design a drying scheme and configure the unit, which will save you a lot of money! All the above technical trends about EPC coating drying equipment and dehumidifier in EPC coating drying room are provided by the electrical appliances for your reference only
